Home / ECMO system in Australia
Buying an ECMO system
ECMO system in Australia: the Lifemotion ECMO system, supplied and supported locally
The Lifemotion ECMO system is an extracorporeal membrane oxygenation (ECMO) system made up of a console, a centrifugal pump head, a membrane oxygenator and ECMO circuit sets. In Australia it is supplied by OHM Healthcare, the exclusive distributor for Australia and New Zealand and the ARTG sponsor, and supported locally by our clinical engineers.
Request a demonstration Regulatory and ARTG
What this page covers
This page is for hospital, retrieval-service, procurement and biomedical engineering teams who are looking at an ECMO system (often called an ECMO machine) in Australia. It sets out what the Lifemotion ECMO system consists of, its ARTG entries, the manufacturer's published specifications, where the system is used, and what OHM Healthcare does locally. It does not give prices; ask us for a quotation.
Components and ARTG entries
The system has four core components. Each has its own page and its own entry on the Australian Register of Therapeutic Goods (ARTG).
Accessories listed by the manufacturer include the trolley, the Lifemotion Frame (a lightweight support frame for the pump driver and battery), a backpack, an emergency hand crank and a battery charger bank. The entries are set out on the Regulatory and ARTG page.
Manufacturer's published specifications
The figures below are the manufacturer's published figures. The source is shown for each row. Performance data are measured under the test conditions given in the Instructions for Use.
| Item | Manufacturer's published figure | Source |
| Console LM-ECMO-1000: main unit size | 380 × 300 × 380 mm (L × W × H); approx. 11 kg, excluding trolley, spare pump drive motor and accessories | Lifemotion brochure, document LM-BD-08-010 V.2, page 21 |
| Console: monitoring | Real-time flow; integrated bubble detection; three pressure sensors (negative pressure, oxygenator inlet, oxygenator outlet) with the pressure differential across the oxygenator calculated; two temperature sensors; non-invasive oxygen saturation; haematocrit and haemoglobin | Lifemotion brochure, document LM-BD-08-010 V.2, pages 4 and 11 |
| Console: set-up guidance | Real-time checklist at start-up; five-step guided priming sequence | Lifemotion brochure, document LM-BD-08-010 V.2, page 4 |
| Console: pump drive | Main pump drive motor, backup pump drive motor and manual hand crank | Lifemotion brochure, document LM-BD-08-010 V.2, page 5 |
| Console: batteries | Two integrated battery packs, each up to 120 minutes of operation depending on system configuration and clinical conditions (brochure); operation time without external power supply 100 to 240 minutes (Instructions for Use) | Lifemotion brochure, document LM-BD-08-010 V.2, page 6; Lifemotion Console Instructions for Use, ED12-UD-030 A1 |
| Console: connectivity | HL7-based integration through a standard Ethernet interface (RJ45) | Lifemotion brochure, document LM-BD-08-010 V.2, page 7 |
| Oxygenator LM-BGEA-1000 | Blood flow range 0.5 to 7.0 L/min; sweep gas flow 0 to 14 L/min; priming volume 300 mL; oxygenation membrane 2.0 m², polymethylpentene (PMP); heat exchanger 0.4 m², PET; blood inlet and outlet 3/8 inch | Lifemotion brochure, document LM-BD-08-010 V.2, page 15 |
| Centrifugal pump head LM-PH-1000 | Flow up to 7.0 L/min; speed up to 6,500 rpm; priming volume 17 mL; magnetically driven impeller on a single-point pivot | Lifemotion brochure, document LM-BD-08-010 V.2, pages 17 and 18 |
| ECMO set LM-TPS-1000 | Pre-assembled sterile circuit with pump head, oxygenator and tubing set; sensors for pressure, temperature, flow and bubble detection; tube length 2.2 m | Lifemotion brochure, document LM-BD-08-010 V.2, page 12 |
| ECMO set LM-TPS-1000L | As LM-TPS-1000, with tube length 2.65 m | Lifemotion brochure, document LM-BD-08-010 V.2, page 12 |
| ECMO set LM-TPS-1500L | Adds integrated sensors for haematocrit, haemoglobin and oxygen saturation; tube length 2.65 m | Lifemotion brochure, document LM-BD-08-010 V.2, page 12 |
| Blood-contacting surfaces | Phosphorylcholine coating on the oxygenator, pump and ECMO sets | Lifemotion brochure, document LM-BD-08-010 V.2, page 13 |
The manufacturer is Lifemotion Medical Technology Co., Ltd. (lifemotionmedical.com). Product availability and specifications are subject to the locally approved Instructions for Use.
Where the system is used
The system is described for three settings, each within the approved configurations and the Instructions for Use:
- The intensive care unit: the full system on its trolley at the bedside.
- Emergency settings: the portable console and guided set-up (start-up checklist and five-step priming).
- Retrieval and transport: the portable console or the core module, with carrier solutions developed with Starmed GmbH for ground and air transport (availability varies by region; use per the locally approved IFU).
An overview is on the Applications page.
What to check when acquiring an ECMO system
These are procurement and engineering points to cover with any ECMO supplier. They are not clinical advice.
- Regulatory status: the ARTG entry for each component you intend to buy, and the Instructions for Use that apply.
- Configuration: bedside, transport, or both, and the accessories each one needs.
- Consumables: which circuit set suits your service, and how supply will be planned. OHM Healthcare holds stock of Lifemotion consumables in Australia.
- Training: who will be trained, and when, before the system goes into service.
- Service: installation and commissioning, preventive maintenance, repair, and where the equipment fits in your biomedical maintenance programme under AS/NZS 3551.
- Integration: HL7 data exchange with hospital systems, if required.
Further reading: ECMO procurement guide for Australian hospitals, choosing an ECMO system: key questions for procurement teams and how to set up an ECMO programme in an Australian hospital. More articles are in Resources, and common questions are answered in the FAQ.
Local supply and support from OHM Healthcare
OHM Healthcare is the exclusive distributor of the Lifemotion ECMO system in Australia and New Zealand, and the ARTG sponsor. It is an engineer-led company that holds ISO 9001:2015 certification. Its head office is in Melbourne, it has an office in Sydney, and it provides service across Australia and New Zealand.
Every Lifemotion ECMO system that OHM Healthcare supplies is supported by our clinical engineers: installation, training for the teams who use and maintain the system, preventive maintenance and repair. See Local Support. For New Zealand, see Lifemotion ECMO in New Zealand.
Arrange a demonstration or a quotation
Demonstrations can be arranged for ICU, perfusion, retrieval, procurement and clinical engineering teams.
OHM Healthcare: phone 03 9115 7464, email sales@ohmhealthcare.com.au, or use the contact page.
Frequently asked questions
Who supplies the Lifemotion ECMO system in Australia?
OHM Healthcare is the exclusive distributor of the Lifemotion ECMO system in Australia and New Zealand, and the ARTG sponsor.
Does the Lifemotion ECMO system have ARTG entries?
Yes. Console LM-ECMO-1000: ARTG 528964. Membrane oxygenator LM-BGEA-1000: ARTG 528771. Centrifugal pump head LM-PH-1000: ARTG 528772. ECMO circuit sets LM-TPS-1000, LM-TPS-1000L and LM-TPS-1500L: ARTG 528773.
What does the Lifemotion ECMO system consist of?
A console, a disposable centrifugal pump head, a disposable membrane oxygenator and ECMO circuit sets, which work together as one extracorporeal life support circuit. Accessories include a trolley, a lightweight frame for the pump driver and battery, a backpack and a battery charger bank.
Can the system be used for retrieval and transport?
The manufacturer describes a portable console and a core module for mobility, with carrier solutions developed with Starmed GmbH for ground and air transport. Use in transport is subject to the approved transport configurations and the Instructions for Use.
Who installs and services the system?
The clinical engineers at OHM Healthcare install the system, train the teams who use and maintain it, and carry out preventive maintenance and repair. Head office is in Melbourne, with an office in Sydney, and service is provided across Australia and New Zealand.
How do we get a price or a demonstration?
Prices are not published. Contact OHM Healthcare on 03 9115 7464 or sales@ohmhealthcare.com.au for a quotation or to arrange a demonstration.
For healthcare professionals and healthcare organisations. Product availability and specifications subject to the locally approved Instructions for Use.